ELECTROMEN
EM-291A is brushless DC-motor driver for motors with hall sensor feedback. The unit has a mosfet power stage with good efficiency
and it meets also todays EMC requirements. The unit has the basic digital command inputs like direction, start/stop, and analog
input for speed control. Device has one NPN output for fault and overcurrent indication use. Indication output functions can be
defined with parameter. The fault situations are also indicated with on-board LED.
There are two control options for speed. Direct control ( open loop ) sets motor voltage in propotion to control voltage as with
a standard DC-motor. Closed loop mode uses hall sensor feedback for speed control. This mode offers good speed regulation.
Start and stop ramps are working in both mode. Speed adjust range, closed loop rpm range and ramps can be set with parameters.
Analog input is filtered, so that also PWM signal of PLC can be used to control speed.
Parameter setting can be done digitally with EM-236 interface unit or with Emen-Tool lite PC-programand EM-268 adapter. There is also
an option to use iPhone with Ementool-APP and EM-326 adapter. The Parameters settinfg are stored into driver's nonvolatile memory .
The parameter interfaces can be also used for motor current monitoring.
Driver card can be installed in DIN-rail base and some enclosure options are also available.
FEATURES
- Three phase output
- Speed adjustment
- Current limit and trip.
- Open/closed loop modes
- Settable Indication output
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
Częstotliwość PWM | 16kHz |
---|---|
Dostawca | Electromen |
Maksymalny prąd ciągły | 4 A |
Masa | 78 g |
Montaż | szyna DIN |
Napięcie zasilania | 12 V DC, 24 V DC |
Odpowiedni silnik | Bezszczotkowy DC |
Prąd szczytowy | 6 A |
Rodzaj sterowania | Prędkość, Kierunek, Moment, Soft start/stop |
---|---|
Sygnał niski - logiczne 0 | <1V = OFF |
Sygnał wysoki - logiczne 1 | >4V = ON |
Wejście analogowe | 0-5V lub 0-10V |
Wymiary dł x sz x wy | 72x65x20 mm mm |
Zakres ustawień prądu | 0.1-6 A |
EM-291A is brushless DC-motor driver for motors with hall sensor feedback. The unit has a mosfet power stage with good efficiency
and it meets also todays EMC requirements. The unit has the basic digital command inputs like direction, start/stop, and analog
input for speed control. Device has one NPN output for fault and overcurrent indication use. Indication output functions can be
defined with parameter. The fault situations are also indicated with on-board LED.
There are two control options for speed. Direct control ( open loop ) sets motor voltage in propotion to control voltage as with
a standard DC-motor. Closed loop mode uses hall sensor feedback for speed control. This mode offers good speed regulation.
Start and stop ramps are working in both mode. Speed adjust range, closed loop rpm range and ramps can be set with parameters.
Analog input is filtered, so that also PWM signal of PLC can be used to control speed.
Parameter setting can be done digitally with EM-236 interface unit or with Emen-Tool lite PC-programand EM-268 adapter. There is also
an option to use iPhone with Ementool-APP and EM-326 adapter. The Parameters settinfg are stored into driver's nonvolatile memory .
The parameter interfaces can be also used for motor current monitoring.
Driver card can be installed in DIN-rail base and some enclosure options are also available.
FEATURES
- Three phase output
- Speed adjustment
- Current limit and trip.
- Open/closed loop modes
- Settable Indication output
- Good efficiency
- Low EMC emissions
- DIN-rail mountable
Firma Technosoft specjalizuje się w opracowywaniu inteligentnych napędów, łączących w sobie sterownik silnika i kontroler ruchu w jednym urządzeniu, w celu realizacji złożonych funkcji ruchu.
Pojazdy AGV wymagają wyspecjalizowanych kontrolerów ruchu, niezawodnych i dających duże możliwości programowania. Taki właśnie jest iGVD71 firmy Technosoft.
Seria 3000 od firmy PR Electronics to moduły cechujące się wysoką dokładnością przetwarzanych sygnałów w pełnym zakresie, szybkim czasem odpowiedzi oraz wąską obudową, która ma zaledwie 6,1 mm.
Firma Epec oferuje kompleksowe rozwiązania IoT do zdalnego serwisowania, diagnostyki, zarządzania flotą, monitorowania stanu, wskaźników KPI maszyn , które są dopasowane do zindywidualizowanych potrzeb klienta.
Przetworniki firmy WIKA są bardzo trwałe, mają zakres ciśnień od -1 do 15 000 bar, przyłącza procesowe G1/4" i G1/2" oraz sygnały wyjściowe 4-20 mA lub 0-10 V. Zachęcamy do kontaktu z nami, aby dobrać odpowiedni przetwornik ciśnienia do Państwa potrzeb.
Drukarka termotransferowa Cembre MG4 ma za zadanie nadrukowywać znaczniki, identyfikatory, naklejki informacyjne, opisy oraz etykiety do identyfikacji przewodów, urządzeń oraz komponentów elektrycznych.
|
|
|
|
|
||
---|---|---|---|---|---|---|
|
|
|
|
|
||
|
|
|
|
|
||
|
|
|
|
|
||
|
|
|
|
|
||
|
|
|
|
|
||
|
|
|
|
|
Warianty produktu | Cena | ||
---|---|---|---|
![]()
Sterownik silnika BLDC, 2Q, 12-35V DC, 4A
Nr produktu:
EM-291A
Skopiowano
|
|
Wybierz wariant produktu z listy
Product Manager SILNIKI I MOTOREDUKTORY
Jeśli potrzebujesz pomocy skontaktuj się z nami: