ELECTROMEN
EM-324-SAF is a positioning driver to be used with DC-motors. The solid state power stage operates with high efficiency as it is
realized with FET-transistors. Its literally everlasting compared to relay solutions. Control and feedback is done with analog signal.
Control signal can be a voltage in range of 0 to 11V or current from 0 to 20mA. Feedback signal can be in the range from 0 to 11V.
Driver supports also a potentiometer feedback, with auxiliary voltage outputs of 0V and 5,5V to exitate the potentiometer.
The max. accuracy available for positioningof is 0,2% that is adequate for most actuator positioning applications.
The settings and adjustments are done with parameters as in all new generation Electromen products. Movement range can be
modified from both ends with SW-limit parameters. Current limits and driving speeds can be set individually for both directions.
Driver includes also many other dynamic adjustment possibilities like parameters for load compensation, dead-zone setting
(positioning window), start and stop ramps for a smooth direction change and braking zone for well operating positioning.
The parameter setting and status monitoring is done with EM-236 Interface Unit. With EM-236 the right parameters can also be
easily copied to other driver units. The on-board LED-light indicates the possible fault situations with blinking codes. If needed,
the fault can be forwarded trough combiport to other driver cards. Alternatively this port can be set to give out the "position OK"
information or it can even indicate the position with an analog voltage signal. Device is EMC tested for industrial and household
environment and operating temperature range is quite wide.
There are also some housing options available for EM-241-SAF driver card.
FEATURES
- analog feedback
- multiple dynamic settings
- solid state power stage
- one or two pulse feedback
- voltage or mA control
- position accuracy max. 0.2%
- versatile setting options
- digitally settable parameters
- housing options available
- 2/16kHz pwm frequncy options
- CE marked product
* 4A at 2kHz / 3A at 16kHz mom. 6A ( Ta<50°C )
Częstotliwość PWM | 2kHz/16kHz |
---|---|
Dostawca | Electromen |
Masa | 80 g |
Montaż | szyna DIN |
Napięcie zasilania | 12 V DC, 24 V DC |
Odpowiedni silnik | Szczotkowy DC |
Prąd szczytowy | 6 A |
Rodzaj sterowania | Prędkość, Kierunek, Moment, Pozycja, Soft start/stop |
Sygnał niski - logiczne 0 | <1V = OFF |
---|---|
Sygnał wysoki - logiczne 1 | >4V = ON |
Temperatura pracy | -40°C...+60°C |
Wejście analogowe | 0-5.5V, 0-11V lub 4-20mA |
Wymiary dł x sz x wy | 72x32x25 mm mm |
Zakres ustawień prądu | 0.1-6 A |
EM-324-SAF is a positioning driver to be used with DC-motors. The solid state power stage operates with high efficiency as it is
realized with FET-transistors. Its literally everlasting compared to relay solutions. Control and feedback is done with analog signal.
Control signal can be a voltage in range of 0 to 11V or current from 0 to 20mA. Feedback signal can be in the range from 0 to 11V.
Driver supports also a potentiometer feedback, with auxiliary voltage outputs of 0V and 5,5V to exitate the potentiometer.
The max. accuracy available for positioningof is 0,2% that is adequate for most actuator positioning applications.
The settings and adjustments are done with parameters as in all new generation Electromen products. Movement range can be
modified from both ends with SW-limit parameters. Current limits and driving speeds can be set individually for both directions.
Driver includes also many other dynamic adjustment possibilities like parameters for load compensation, dead-zone setting
(positioning window), start and stop ramps for a smooth direction change and braking zone for well operating positioning.
The parameter setting and status monitoring is done with EM-236 Interface Unit. With EM-236 the right parameters can also be
easily copied to other driver units. The on-board LED-light indicates the possible fault situations with blinking codes. If needed,
the fault can be forwarded trough combiport to other driver cards. Alternatively this port can be set to give out the "position OK"
information or it can even indicate the position with an analog voltage signal. Device is EMC tested for industrial and household
environment and operating temperature range is quite wide.
There are also some housing options available for EM-241-SAF driver card.
FEATURES
- analog feedback
- multiple dynamic settings
- solid state power stage
- one or two pulse feedback
- voltage or mA control
- position accuracy max. 0.2%
- versatile setting options
- digitally settable parameters
- housing options available
- 2/16kHz pwm frequncy options
- CE marked product
* 4A at 2kHz / 3A at 16kHz mom. 6A ( Ta<50°C )
Mechaniczne systemy kontroli dostępu są łatwe w instalacji i służą do otwierania włazów i bram w aplikacjach, w których występuje zagrożenie powodowane przez ruchome części maszyn. W tym artykule dowiesz się więcej o zaletach systemów kontroli dostępu.
Firma Sensit od ponad 30 lat zajmuje się rozwojem i produkcją oporowych czujników temperatury, czujników wilgotności, czujników CO2, czujników poziomu, czujników przepływu i czujników położenia.
Lampy Sangel z serii DualLight zapewniają wysokiej jakości białe światło LED do oświetlenia maszyny oraz jednoczesną sygnalizację stanu przy wykorzystaniu diod LED RGB. Zwiększa to nie tylko wydajność, ale także poprawia bezpieczeństwo w miejscu pracy.
Przetworniki siły i czujniki tensometryczne to urządzenia służące do pomiaru ciężaru lub siły z dużą dokładnością w różnych zastosowaniach.
TL400-I to nowoczesny czujnik poziomu i objętości firmy Novus, który dzięki bezinwazyjnej metodzie detekcji idealnie nadaje się do monitorowania cieczy, ziaren, płynów oraz materiałów sypkich, zarówno w zastosowaniach statycznych, jak i dynamicznych.
PR 5437 jest dwuprzewodowym przetwornikiem z komunikacją HART 7, który oferuje wyjątkową dokładność, możliwość redundancji czujników oraz dodatkowe funkcje wyróżniające go na tle konkurencji.
Wojciech Drabik